Grease Separators
The grease separator is used in industrial and catering facilities, from which fats and oils of animal and vegetable origin can be poured into nature. Their use is mandatory in large kitchens, hotels, hospitals, restaurants, food distribution facilities, slaughterhouses, food processing facilities.

The Ecoplast polyethylene grease separator complies with the SIST EN 1825-1 standard and is produced in 2 parts, from the settling tank and the grease collector. In the sedimentation tank, the inflow of wastewater is calmed, heavier parts are deposited at the bottom. In the grease collector, oil and grease, which have a lower density, separate from the water and remain on the surface. The purified water flows into the drain through the knee, which is immersed below the level of fat in the oil. Grease separators are buried in the ground.

Grease separator is manufactured in accordance with the SIST EN 1825-1 standard.
It is made of resistant and strong polyethylene (LLDPE).
It has a long service life.
If necessary, 100% water can be recycled.
It is waterproof.
Quick and easy installation.
Easy maintenance
Oil Separators
Oil separators are made of polyethylene, which is suitable for clean water and fecal matter.

In accordance with EU directives, oil separators are installed on everything:
at gas stations,
car washes,
parking areas,
open and closed parking lots.
They are intended for the extraction of light water according to European standards SIS EN 858-1 and prEN 858-2.

Atmospheric water mixed with oil and mudflows from asphalt and concrete surfaces into the sewer system or into nature. Oil separators are designed to clean water from mud and oil. For optimal effect, a two-chamber tank is most often used. The first part of the tank is used as a settling tank , and in the second part the oil separates from the water.

Inside the Reservoir
Inside the separator, the sludge is separated as follows:
With oil and mud, dirty water enters the tank.
Using a specially patented water distribution system, the water is evenly distributed throughout the tank.
Long chamber, where it is already purified from sludge.
Under the second part of the tank the oil is separated from the water.
With a specially patented system for distribution of water, water and oil are evenly distributed throughout the tank. Larger oil droplets are on the surface, due to the high density. Smaller droplets combine and increase in volume in the filter, and rise to the surface. This makes it easier for companies engaged in cleaning waste oils.
The water that flows out of the separator is pure-purified water.


The excavation should be about 50 cm larger than the dimensions of the separator.
A layer of sand must go next to the tank, and it is gradually buried.
It is necessary to check the terrain under the tank, it must be well trodden.
Separator placed on a lower level, must be protected by a reinforced structure.
It is necessary to make sure that there are no sharp objects that would damage the tank.

Instructions for installation on site with groundwater
Due to groundwater, the oil separator must be fixed, ie anchored. At the bottom of the pit, it is necessary to concrete a concrete slab with anchoring threads. The tank must be connected to anchor with polyester strips.

Fill the entire system with water due to the perfect operation of the separator, high groundwater that could lift the tank. Secure clean sensors in the electronic alarm device.

Separatori Class 1
Separate water, mineral oils and solid parts touch the oil separators ... Mineral oils include all motor fuels, lubricants, oils, which have a lower density of 0.95 g / cm3-Oil separators are used for water purification indoors (mechanical workshops , production, gas stations) and open spaces (parking lots, landfills, platforms).

Oil Separators
The first group has a built-in coalescent filter and is used where atmospheric and process wastewater is discharged into surface water, ie. Surroundings.

Separators of the second class are used where atmospheric and process wastewater is discharged into the sewer.
The wall separates the settling chamber and the chamber for collecting mineral oils. Due to the composition of the cholescent filter and the physical properties of mineral oils (lower density than water), oil droplets are retained and float to the surface more efficiently.

Oil separators are manufactured in accordance with the standard SIST EN 858-1, SIST EN 858-2 and the ordinance in accordance with the Law on Construction Products NN 86/08. , and group II with a term load of 100mg.
Oil Separators With ByPass
They are intended for large flows (parking lots).
They are manufactured so that at the beginning of the water inflow flows into the separator, and flows through a coalescent filter, and later drains directly to the east. wall.
Coalescent Filter is mounted on the partition wall for more efficient separation of water and oil
Manhole oil separators
Separatori ulja su u dva izvršenja, ugrađeni su u šahte od polietilena, sa ili bez koalescentnog filtra.

Dimenzionisanje Kapaciteta
Za pravilno dimenzioniranja separatora ulja potrebni su podaci:
lokacija ugradnje, površina s koje se sakuplja voda u separator ulja, namjena površina sa kojih se sakuplja voda u separator ulja, tip otpadna vode koja dotiče u separator ulja.

Proizvedeni su od trajnog polietilena, laka i jednostavna ugradnja, vodo nepropusnost, jednostavno održavanje, konkurentne cijene.
google-site-verification: google55bb4fb07fa1308a.html